Maker Faire Bay Area

Hi All!

Makerfaire 2012 Bay Area

I’m still (slowly) working on my Surfer Tee, but I’ve taken a brief hiatus to go to (and recover from) Maker FaireCraftsy had a big booth with lots of fun make & takes.  With over 10,000 fairegoers, we were BUSY!

Makerfaire 2012 Bay Area

Makerfaire 2012 Bay Area

Maker Faire was such a great experience! It’s been described to me as a Burning Man for makers…and it’s a pretty apt description!

Makerfaire 2012 Bay Area

In addition to meeting lots of awesome crafter / makers and seeing so many amazing robotics, light sculptures, and bike hacks, I learned to solder from the amazing Kate Richbourg, who is so fun and a really amazing teacher! Here she is in her booth, looking adorable:

Makerfaire 2012 Bay Area

Check out the music stage in the pic below…all pedal – power! My neighbor says he wants one of these bike generators to power his TV. Sounds like a good idea!

Makerfaire 2012 Bay Area

Surfer tee: how to add waist shaping

This is a very poor sketch of the basic measurements that you’ll need to take:

20120513-204440.jpg

The measurements are:
1. Bust
2. Waist
3. High hip
A. Bust to waist
B. Waist to hip

Take these measurements and write them down.

Mine are:
42, 36, 41, 5, 4 inches, respectively. Now that I know these measurements, I can use my gauge to figure out how many sts to decrease for the waist and when to work them.

I don’t want a super fitted waistline, I just want to take it in about an inch on each side, and then increase back out for the hip.

Another measurement I’m going take is from under arm to waist, which on me is about 9 inches.

Gauge:4.5 sts & 6 rows to one inch.

If I want to take the sweater in by about an inch on each side, I’ll need to decrease 4 stitches before the piece is 9 inches (54 rows) long from the under arm.

I like the slope created by working the decreases about 8 rounds apart, so I want to start them 54 -16 = 38 rows from the under arm.

Then, I’ll need to increase back up to my desired number of stitches for the hip. I like this slope to be made of increases about 6 rows apart. I’ll work those increase rounds, then knit to desired length before hem.

Surfer Tee progress: Joined and almost to the waist shaping.

Here’s Olive wearing her surfer tee, while holding MY surfer tee.  This might fall under the category of Double Dealing (how hilarious are my glasses in that post!?) but then again, she’s just a baby!

Olive with the Surfer Tee

More Olive:
Olive with the Surfer Tee

You can see how the neckline is going to come together by looking at hers. I can’t wait!!

I dyed this yarn myself using low-impact dyes in the crockpot…what feels like AGES ago with my friend, Cindy.  It’s got some white spots where I had tied the skein to keep it from tangling.  See how every so often there’s one white stitch? So, I think I’ll have to go back with a paint brush and touch those spots up when I’m done.  Maybe it won’t bother me as much when the whole thing’s knit, but they’re driving me crazy now.

How my dark batch came out

In general, though, I love the color! It looks much darker in the hank than it does knit up.  I think I did a good job of adding depth to the color without it taking on a trippy look, and of keeping it from pooling.   So far, it looks like I’ll have plenty of yarn for at least a short-sleeved yarn with pockets.  Would have been handy to have some notes on the yarn!  I know it’s a BFL, and a light worsted weight.  I’m using 7s and I like the fabric I’m getting.  If I went up to 8s, it’d be too loose a weave for my taste.

Olive with the Surfer Tee

I threw some bust darts into the front of my sweater, and now I’m just knitting down to a few inches below the bust, so that I can do a bit of waist shaping.

The pattern isn’t written to have any shaping, but I’m going to put some in this one. Tune in next time to see how I do it. I’m not going to do a full calculation like I do in my Fit Your Knits class, but I’ll show you how to nip in the waist a bit for a more flattering silhouette. I left it out of the original pattern because this is really meant to be a sweater that you pull on over a tee or Henley, a great casual top layer.  When I designed it, I wouldn’t have wanted (or needed) a shaped waist at all (Olive was about 6 months old!)

I’m actually finally losing some baby weight and want mine to be a bit more fitted.

YEA! PROGRESS!

Surfer Tee progress…how to separate the sleeves

I haven’t knit a sweater for myself in a while! I’m excited to have this one in my size. I think that I may just have a chance to wear it if I can get it finished up in the next few days.

Last night I stayed up knitting until I finished the yoke.

Surfer Tee in progress

The first couple of rows are pretty easy. They set up the increase structure and the simple lace repeat for the front details.

Next, you’re instructed to repeat the last 2 rows a certain number of times. This does mean to repeat them x more times, ending with a WS row (ready to work a RS row.)

In the above photo, I’ve worked through all of the increase rows and have started the Separate Sleeves and Join the Body section.

Surfer Tee in progress

Here, I’m using a darning needle and length of yarn recycled from my swatch to put the second sleeve on waste yarn.

Surfer Tee in progress

I’m ready to knit around to the second front, and start working in the round.

How are your Surfer Tees coming??